ASN Wikibase Occurrence # 161548
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can
submit corrected information.
Date: | Saturday 19 October 2013 |
Time: | 11:32 |
Type: | Zenair STOL CH 701 |
Owner/operator: | Private |
Registration: | N538HB |
MSN: | 1001 |
Year of manufacture: | 2012 |
Total airframe hrs: | 43 hours |
Engine model: | GREATPLAINS GREATPLAIN VW |
Fatalities: | Fatalities: 0 / Occupants: 2 |
Aircraft damage: | Substantial |
Category: | Accident |
Location: | 3944 Gall Blvd, Zephyrhills, Pasco, FL -
United States of America
|
Phase: | Take off |
Nature: | Private |
Departure airport: | Zephyrhills, FL (ZPH) |
Destination airport: | Zephyrhills, FL (ZPH) |
Investigating agency: | NTSB |
Confidence Rating: | Accident investigation report completed and information captured |
Narrative:The pilot reported that, while in the traffic pattern at his home airport practicing touch-and-go landings, the experimental, amateur-built airplane experienced a complete loss of thrust from the propeller. While turning from the crosswind leg of the traffic pattern onto the downwind leg of the traffic pattern, the engine suddenly “overreved.” The pilot reduced power and chose to perform an emergency landing. He then tried adding power, but the propeller did not respond and was windmilling. He established best glide speed, but the airplane had developed a high sink rate and was losing altitude rapidly. He then slowed the airplane as it approached a set of powerlines. The airplane clipped one of the powerlines, which nearly severed the left wing. The pilot then “stalled” the airplane and touched down hard. The airplane was substantially damaged during the forced landing.
Examination of the engine revealed that a belt-driven propeller speed reduction unit (PSRU) was installed. Further examination revealed that both drive belts from the PSRU were broken into several pieces, and shredded material from the belts was present throughout the engine compartment. Small pieces of rubber were also present on the forward part of the engine, the propeller hub assembly, and the PSRU pulleys’ grooves. Examination of the broken belts revealed jagged belt fractures and evidence of overheating, hardening, back cracks, land area wear, and “V” rib wear, all of which is indicative of inadequate belt tension, which can cause the belts to slip as they travel around the pulleys and generate heat buildup. The heat buildup can cause the rubber compounds in the belt to break down and crack and lead to a belt failure. According to maintenance records, the drive belts for the PSRU had been replaced about 20 hours of operation before the accident flight.
Probable Cause: The failure of the propeller speed reduction unit drive belts due to inadequate belt tension being applied during installation, which resulted in a complete loss of thrust.
Accident investigation:
|
| |
Investigating agency: | NTSB |
Report number: | ERA14LA004 |
Status: | Investigation completed |
Duration: | |
Download report: | Final report |
|
Sources:
NTSB
Location
Media:
Revision history:
Date/time | Contributor | Updates |
19-Oct-2013 18:32 |
harro |
Added |
20-Oct-2013 04:21 |
Geno |
Updated [Phase, Departure airport, Source, Embed code, Narrative] |
21-Dec-2016 19:28 |
ASN Update Bot |
Updated [Time, Damage, Category, Investigating agency] |
29-Nov-2017 09:17 |
ASN Update Bot |
Updated [Operator, Total occupants, Other fatalities, Nature, Departure airport, Destination airport, Source, Embed code, Narrative] |
The Aviation Safety Network is an exclusive service provided by:
CONNECT WITH US:
©2024 Flight Safety Foundation