ASN Wikibase Occurrence # 180001
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can submit corrected information.
| Date: | Friday 9 July 2004 |
| Time: | 13:00 |
| Type: |  Beech BE-N35 |
| Owner/operator: | Private |
| Registration: | N80HL |
| MSN: | D-6625 |
| Year of manufacture: | 1961 |
| Total airframe hrs: | 4506 hours |
| Engine model: | Continental IO-470-N |
| Fatalities: | Fatalities: 0 / Occupants: 4 |
| Aircraft damage: | Substantial |
| Category: | Accident |
| Location: | near Austin, Minnesota -
 United States of America
|
| Phase: | Landing |
| Nature: | Private |
| Departure airport: | Ankeny, IA (IKV) |
| Chetek, WI (Y23) | |
| Investigating agency: | NTSB |
| Confidence Rating: |  Accident investigation report completed and information captured |
The airplane sustained substantial damage during a forced landing following a loss of engine power in cruise flight. The pilot reported the airplane had been operating properly at 5,000 feet mean seal level (msl) until the propeller started to overspeed between 2,950 - 3,025 rpm and the overspeed annunciator light illuminated. He attempted to slow the propeller with the propeller pitch control but without effect. The oil pressure gauge read zero. He reduced the throttle to about 15 inches of manifold pressure to slow the engine to 2,500 rpm. About 30 seconds to 1 minute later, the airplane began to shake and vibrate violently, white smoke filled the cabin, and oil covered the windshield. The pilot reported that he decided to execute a forced landing to one of the flat farm fields. He lowered the gear and established about a 90 knot descent. He shut down the engine by pulling the mixture to idle cutoff. He slipped the airplane to lose altitude prior to landing. The airplane skidded in the mud for about 80 yards, and the landing gear retracted back into the wheel wells during landing roll out. The on-site inspection of the engine revealed a hole in the right side of the engine case. The engine teardown revealed that number 1 cylinder piston pin plug was fractured in two pieces. The smaller of the two pieces was deformed with substantial material loss with the fracture surface being obliterated. The number 4 cylinder piston pin plug rotated within the piston pin. Metal contamination was found in the oil pressure relief valve and valve seat. There was a hole in the engine case next to the number 5 cylinder. The number 5 connecting rod was broken and the end of the rod was "hammered" and blackened. The number 5 rod bearing was scored and blackened. The number 1, 4, and 6 rod bearings exhibited melting and protruding. All main bearings were scored. The oil pump gears turned freely, and the sides of the pump walls were scored. The number 1 and number 4 cylinder piston pins and piston pin plugs were sent to the National Transportation Safety Board's Materials Laboratory for examination. The examination revealed that the number 1 cylinder piston pin plug had a fracture surface with visible crack arrest lines, features consistent with fatigue. Black deposits were observed on the head of the larger piece of the number 1 piston pin plug and on the ends of the number 4 cylinder piston pin plugs, although the deposits were less thick than on the number 1 piston pin plug. An impression was observed on the larger piston pin plug piece in the bevel between the head and the shank. The impression was located on the same side of the piston pin plug as the fatigue origin. The surface of the impression was covered with black deposits. The pilot reported the engine had 1,000 hours of operation since the last overhaul, and 47.7 hours of operation since the last inspection. The engine did not have an oil filter installed on it.
Probable Cause: The loss of engine power due to the fatigue fracture of the piston pin plug that lead to engine oil starvation/exhaustion and the subsequent overload fracture of the piston rod and crankcase.
Accident investigation:
 |
|
Sources:
NTSB: https://www.ntsb.gov/_layouts/ntsb.aviation/brief.aspx?ev_id=20040715X00982&key=1
Revision history:
| Date/time | Contributor | Updates |
|---|---|---|
| 29-Sep-2015 13:32 | Noro | Added |
| 21-Dec-2016 19:30 | ASN Update Bot | Updated [Time, Damage, Category, Investigating agency] |
| 07-Dec-2017 18:10 | ASN Update Bot | Updated [Other fatalities, Departure airport, Destination airport, Source, Narrative] |
Corrections or additions? ... Edit this accident description
The Aviation Safety Network is an exclusive service provided by:
Quick Links:
| ASN Home | Send Correction / Feedback |
| FSF Home | Disclaimer | Copyright |
| Contact Us | Privacy Policy |
| Press / Media |
CONNECT WITH US:
©2024 Flight Safety Foundation