ASN Wikibase Occurrence # 215330
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can
submit corrected information.
Date: | Wednesday 12 September 2018 |
Time: | 12:45 |
Type: | Rotary Wing RW-1 |
Owner/operator: | Private |
Registration: | N166LC |
MSN: | 001 |
Year of manufacture: | 2015 |
Total airframe hrs: | 89 hours |
Engine model: | SOLAR T62-32 |
Fatalities: | Fatalities: 1 / Occupants: 1 |
Aircraft damage: | Substantial |
Category: | Accident |
Location: | Billings Logan International Airport (KBIL), Billings, MT -
United States of America
|
Phase: | Manoeuvring (airshow, firefighting, ag.ops.) |
Nature: | Private |
Departure airport: | Billings-Logan International Airport, MT (BIL/KBIL) |
Destination airport: | Billings-Logan International Airport, MT (BIL/KBIL) |
Investigating agency: | NTSB |
Confidence Rating: | Accident investigation report completed and information captured |
Narrative:The pilot, who did not hold a helicopter rating, was maneuvering his experimental amateur-built helicopter around the airport area. An acquaintance of the pilot stated that the accident pilot would regularly hover-taxi around the airport area testing the helicopter. The acquaintance also stated that, on the day of the accident, the pilot mentioned that the helicopter was flying well and that he did not have any issues with it. Afterward, the pilot started the helicopter and departed to the west and hover-taxied around the row of hangars back to his hangar. The acquaintance reported that he did not see the accident but that he heard the sound of the helicopter impacting a hangar.
Postaccident examination of accident site showed that the helicopter's main rotor blades had collided with the top section of the hangar and that the helicopter came to rest oriented upward on an angle of about 30° and against the front of the hangar on a westerly heading. It is likely that, during the hover-taxi, the accident pilot ascended above a hover to the height of the hangars before colliding with one.
The left anti-torque pedal for the pilot's right-seat position had failed where the horizontal and vertical tubes met. Notwithstanding the failed anti-torque pedal, examination of the airframe and engine found no mechanical anomalies that would have precluded normal operation of the helicopter.
A metallurgical examination of the fractured horizontal and vertical components of the pilot's right seat's left anti-torque pedal assembly revealed that they failed from a lack of complete fusion at a fillet joint, which led to an overstress fracture. The fractured pedal tube assembly consisted of two aluminum tubes joined together with a filler metal that was consistent with a zinc solder alloy. However, the right anti-torque pedal tube assembly, which was intact, consisted of alloy steel tubes that were welded together with an alloy steel filler metal. The intact tube assembly had a much stronger quality due to the welding process and the inherent higher mechanical properties of the steel than those of the fractured tube assembly.
A build ledger for the helicopter revealed that the anti-torque pedals had been fabricated in December 1996 by the previous owner, almost 20 years before the accident pilot purchased the helicopter. However, the ledger did not detail the fabrication differences among the anti-torque pedals.
The investigation could not determine if the left anti-torque pedal for the right-seat position failed before the impact with the hangar or during the impact sequence. Although the pilot might have been able to control the helicopter after the pedal failed, that possibility would be unlikely given the pilot's minimal experience in helicopters.
Probable Cause: The pilot's failure to maintain clearance with a hangar while maneuvering to his hangar. Contributing to the accident was the pilot's limited experience in helicopters.
Accident investigation:
|
| |
Investigating agency: | NTSB |
Report number: | WPR18FA260 |
Status: | Investigation completed |
Duration: | 1 year and 11 months |
Download report: | Final report |
|
Sources:
NTSB
FAA register:
https://registry.faa.gov/aircraftinquiry/NNum_Results.aspx?NNumbertxt=166LC Location
Images:
Photo: NTSB
Revision history:
Date/time | Contributor | Updates |
13-Sep-2018 06:08 |
gerard57 |
Added |
13-Sep-2018 06:09 |
gerard57 |
Updated [Date] |
13-Sep-2018 14:23 |
Geno |
Updated [Time, Aircraft type, Registration, Cn, Location, Source, Narrative, Plane category] |
15-Aug-2020 16:01 |
ASN Update Bot |
Updated [Time, Departure airport, Destination airport, Source, Damage, Narrative, Accident report, ] |
15-Aug-2020 16:42 |
harro |
Updated [Departure airport, Destination airport, Source, Narrative, Photo, Accident report, ] |
The Aviation Safety Network is an exclusive service provided by:
CONNECT WITH US:
©2024 Flight Safety Foundation