ASN Wikibase Occurrence # 166664
This record has been locked for editing.
Date: | Saturday 31 May 2014 |
Time: | 09:44 |
Type: | Van's RV-6 |
Owner/operator: | Private |
Registration: | N6RP |
MSN: | 23075 |
Year of manufacture: | 2006 |
Total airframe hrs: | 247 hours |
Engine model: | SUBARU EJ 25 |
Fatalities: | Fatalities: 0 / Occupants: 1 |
Aircraft damage: | Substantial |
Category: | Accident |
Location: | north of Suffolk Executive Airport (KSFQ), Suffolk, VA -
United States of America
|
Phase: | Landing |
Nature: | Private |
Departure airport: | South Boston, VA (W78) |
Destination airport: | Suffolk, VA (SFQ) |
Investigating agency: | NTSB |
Confidence Rating: | Accident investigation report completed and information captured |
Narrative:According to the pilot, who was also the owner/builder of the experimental amateur-built airplane, while operating about 2,000 ft mean sea level, the engine rpm went to redline, the airplane lost thrust, and a red fluid covered the windscreen. The pilot attempted a forced landing to a field, but the airplane impacted trees, which resulted in substantial damage to the wings and fuselage.
Postaccident examination of the engine revealed no mechanical malfunctions or anomalies to the engine or gearbox. Examination of the propeller showed that the fine pitch stop nuts were missing. The propeller needle thrust bearing and mating parts were galled, burned, and damaged from rotational and thermal wear. The heat damage likely initiated at the needle thrust bearing and progressed both fore and aft to the blade pin spool and slave piston collar, respectively. The Delrin bushing melted after the heat reached the blade pin spool, which allowed the propeller pins to make bare metal contact with the spool pin slots. With the absence of stop nuts, the propeller blade angle could decrease below a 0-thrust angle, and the melted Delrin bushings allowed the propeller blade angles to decrease an additional 6 degrees in the negative direction. The cumulative effect of both events was a total loss of aerodynamic thrust.
About 28 flight hours before the accident, the pilot/builder used a viscous lubricant to grease the bearings in the propeller assembly. According to the lubricant manufacturer, the lubricant has a high viscosity and was designed for low-speed automotive and trucking applications not for aviation use. Lubricants with high viscosities can cause the bearing to skid, which can result in rapid overheating and failure of the bearing.
Probable Cause: The pilot/builder's decision to use a lubricant that was not designed for high-speed aviation applications, which resulted in the failure of the propeller needle thrust bearing due to the loss of lubrication from overheating, a total loss of aerodynamic thrust, and a subsequent forced landing.
Accident investigation:
|
| |
Investigating agency: | NTSB |
Report number: | ERA14LA272 |
Status: | Investigation completed |
Duration: | |
Download report: | Final report |
|
Sources:
NTSB
History of this aircraft
Other occurrences involving this aircraft Location
Revision history:
Date/time | Contributor | Updates |
01-Jun-2014 00:56 |
Geno |
Added |
01-Jun-2014 23:06 |
Geno |
Updated [Aircraft type, Registration, Cn, Operator, Source, Narrative] |
06-Aug-2016 06:53 |
junior sjc |
Updated [Operator, Narrative] |
21-Dec-2016 19:28 |
ASN Update Bot |
Updated [Time, Damage, Category, Investigating agency] |
01-May-2017 06:46 |
junior sjc |
Updated [Location, Source, Narrative] |
29-Nov-2017 14:24 |
ASN Update Bot |
Updated [Operator, Other fatalities, Departure airport, Destination airport, Source, Narrative] |
The Aviation Safety Network is an exclusive service provided by:
CONNECT WITH US:
©2024 Flight Safety Foundation