ASN Wikibase Occurrence # 170376
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can
submit corrected information.
Date: | Sunday 4 September 2011 |
Time: | c 15:00 LT |
Type: | Bell 205 |
Owner/operator: | Kern Co Fire Department |
Registration: | N205WW |
MSN: | 30329 |
Year of manufacture: | 1980 |
Total airframe hrs: | 3560 hours |
Engine model: | Honeywell T5317B |
Fatalities: | Fatalities: 0 / Occupants: 1 |
Aircraft damage: | Substantial |
Category: | Accident |
Location: | near Tehachapi, CA -
United States of America
|
Phase: | Manoeuvring (airshow, firefighting, ag.ops.) |
Nature: | Fire fighting |
Departure airport: | Tehachapi, CA |
Destination airport: | Tehachapi, CA |
Investigating agency: | NTSB |
Confidence Rating: | Accident investigation report completed and information captured |
Narrative:During an external load operation to drop water on a fire, the helicopter was about 100 feet above ground level at 10 knots when the engine rpm light illuminated and the low rotor rpm horn sounded. The emergency procedures section of the flight manual states that in the event of an engine failure or low rpm, a red light will illuminate and an audio signal will sound when the audio switch is in the AUDIO position. The flight manual instructs the pilot to immediately execute an autorotative descent. The pilot released the water, and made a left-pedal turn to exit the canyon and move away from the fire. He checked his engine rotor rpm gauge and saw that the needles had split: the rotor needle was at the 4-5 o'clock position, and the engine needle was at the 6-o'clock position, which he stated indicated maximum rpm. He maneuvered to establish an autorotation into a landing zone. The helicopter sustained substantial damage to the airframe and tail boom as the result of a hard landing, which collapsed the landing skid.
Postaccident examination discovered that the N2 tachometer drive shaft was sheered as a result of torsional overstress. The N2 tachometer drive delivers engine rpm readings to the cockpit engine tachometer; failure of the N2 tachometer drive would send erroneous engine rpm readings to the cockpit. Accordingly, the pilot's instruments indicated that there was an engine overspeed, but the warning lights and audio were indicating a low power condition. The pilot elected to perform an autorotative landing in accordance with the flight manual instructions for a low rotor rpm.
Probable Cause: The pilot's inability to adequately execute an emergency autorotation due to the flight's low altitude during external load operations, which resulted in a hard landing. Contributing to the accident was a torsionally overstressed tachometer shaft, which sent erroneous engine rpm readings to the cockpit.
Accident investigation:
|
| |
Investigating agency: | NTSB |
Report number: | WPR11GA431 |
Status: | Investigation completed |
Duration: | |
Download report: | Final report |
|
Sources:
NTSB:
https://app.ntsb.gov/pdfgenerator/ReportGeneratorFile.ashx?EventID=20110906X05207&AKey=1&RType=HTML&IType=GA Location
Revision history:
Date/time | Contributor | Updates |
08-Oct-2014 18:15 |
Aerossurance |
Added |
21-Dec-2016 19:28 |
ASN Update Bot |
Updated [Time, Damage, Category, Investigating agency] |
27-Nov-2017 17:12 |
ASN Update Bot |
Updated [Cn, Operator, Other fatalities, Nature, Departure airport, Destination airport, Source, Narrative] |
22-Sep-2020 07:01 |
Aerossurance |
Updated [Time, Operator, Other fatalities, Location, Source] |
16-Nov-2022 09:22 |
Ron Averes |
Updated [Operator] |
30-May-2023 00:21 |
Ron Averes |
Updated [[Operator]] |
The Aviation Safety Network is an exclusive service provided by:
CONNECT WITH US:
©2024 Flight Safety Foundation