ASN Wikibase Occurrence # 284261
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can
submit corrected information.
Date: | Monday 17 September 2007 |
Time: | 12:10 LT |
Type: | Air Tractor AT-802A |
Owner/operator: | U.S. Forest Service |
Registration: | N91357 |
MSN: | 802A-0107 |
Year of manufacture: | 2000 |
Total airframe hrs: | 2872 hours |
Engine model: | Pratt & Whitney Canada PT6A-67AG |
Fatalities: | Fatalities: 0 / Occupants: 1 |
Aircraft damage: | Substantial |
Category: | Accident |
Location: | Big Bear City, CA -
United States of America
|
Phase: | Manoeuvring (airshow, firefighting, ag.ops.) |
Nature: | Fire fighting |
Departure airport: | San Bernardino International Airport, CA (SBD/KSBD) |
Destination airport: | |
Investigating agency: | NTSB |
Confidence Rating: | Accident investigation report completed and information captured |
Narrative:The airplane was loaded with 700 gallons of fire retardant to support fire suppression efforts and the engine chip light illuminated while the pilot was maneuvering to position for a drop at 1,100 feet above ground level. About 20 to 30 seconds later, the pilot heard a loud bang and the engine lost total power. The pilot intentionally ground looped the airplane during a forced landing in an open area in order to avoid a brick wall, fence, and a parking lot containing vehicles and people directly ahead. Examination of the engine revealed the engine lost total power due to the failure of the No. 1 bearing, which resulted in axial and radial movement of the compressor rotor and severe over temperature damage to the gas path components. The bearing failure was due to electrical arcing between the bearing races and rolling elements. The electrical arc pitting of the starter-generator gear shaft indicated a direct electrical arcing path from the starter-generator to the bearing. The exact source of the electrical arcing within the starter-generator was not determined. According to the maintenance records, the starter-generator was replaced 172 hours prior to the accident due to bearing distress. According to a Transport Canada Service Difficulty Advisory, No. AV-2007-05, dated October 29, 2007, in the PT6A engine, electrical arcing occurrences have caused pitting and subsequent failure of the No. 1 bearing. Electrical current travels from the defective starter-generator (SG) spline shaft, through the engine accessory drive train to the engine No. 1 bearing causing mild to severe bearing damage such as pitting, grooves, or craters. The extent of bearing damage, and therefore, the time before failure, is dependent on various factors such as the electrical current, exposure time, bearing load, and rotational speed. The most common and preventable cause of electrical arcing, is from armature leakage occurring as a result of an accumulation of brush dust. This dust can provide an electrical discharge path between the commutator and the shaft. Secondly, a breakdown of the commutator insulation and/or the lamination slots can cause an electrical short. In order to detect pending failure of the No. 1 bearing, the Pratt and Whitney maintenance manual addresses oil contamination monitoring procedures in the event of starter-generator replacement for electrical reasons. The oil filter is to be inspected at 100-hour intervals for engine bearing material for 700 hours following starter-generator installation. There was no record of any subsequent oil filter patch checks or other related inspections after the starter-generator change.
Probable Cause: Loss of engine power while maneuvering due to the failure of the number 1 bearing that was caused by electrical discharge damage to the bearing originating from the starter-generator. Contributing to the accident was the operator's failure to follow the engine maintenance manual procedures for oil monitoring following generator replacement and the unsuitable terrain for the forced landing.
Accident investigation:
|
| |
Investigating agency: | NTSB |
Report number: | LAX07TA277 |
Status: | Investigation completed |
Duration: | |
Download report: | Final report |
|
Sources:
NTSB LAX07TA277
Revision history:
Date/time | Contributor | Updates |
30-Sep-2022 14:06 |
ASN Update Bot |
Added |
12-Nov-2022 01:46 |
Ron Averes |
Updated [Operator, Location, Phase, Nature, Departure airport, Narrative] |
30-May-2023 00:33 |
Ron Averes |
Updated [[Operator, Location, Phase, Nature, Departure airport, Narrative]] |
The Aviation Safety Network is an exclusive service provided by:
CONNECT WITH US:
©2024 Flight Safety Foundation