ASN Wikibase Occurrence # 291893
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can submit corrected information.
| Date: | Saturday 19 August 2006 |
| Time: | 15:39 LT |
| Type: |  McDonnell Douglas MD 500E (369E) |
| Owner/operator: | Columbus City Police |
| Registration: | N554CP |
| MSN: | 0542E |
| Year of manufacture: | 1999 |
| Total airframe hrs: | 6639 hours |
| Engine model: | Rolls-Royce 250-C20B |
| Fatalities: | Fatalities: 0 / Occupants: 2 |
| Aircraft damage: | Substantial |
| Category: | Accident |
| Location: | Columbus, OH -
 United States of America
|
| Phase: | Unknown |
| Nature: | Unknown |
| Departure airport: | Columbus, OH (OH52) |
| Columbus, OH (OH52) | |
| Investigating agency: | NTSB |
| Confidence Rating: |  Accident investigation report completed and information captured |
The public-use helicopter was conducting a routine patrol flight when it experienced an uncontained engine failure. The pilot immediately performed an autorotation and run-on landing to an open parking lot area without further incident. The helicopter was damaged with several punctures with outward deformation consistent with projectile damage originating from an uncontained engine failure. Inspection of the engine revealed that portions of the 1st-stage gas producer wheel had departed the engine. The gas producer turbine tie bolt (part number 23068265, serial number NM81907) was identified as the primary failed component. The tie bolt fractured immediately adjacent to the torque nut. Further examination revealed fracture features consistent with fatigue, initiating at the thread root radius. The microstructure, chemistry, and hardness of the turbine tie bolt met engineering drawing specifications. No material anomalies were detected at the fracture surface. Damage to the fracture surface precluded the determination if the failure was associated with low or high cycle fatigue. The tie bolt had completed 3,427 cycles, about 38 percent, of its published life limit of 9,000 cycles.
The failure was the first documented since the tie bolt was redesigned during the late 1990s. The redesigned tie bolt incorporated a thicker and stiffer cross-section that had a higher resonant frequency. The manufacturer reviewed the testing and analysis that was preformed when the tie bolt was redesigned. Their review confirmed that the current life limit of 9,000 cycles was within design guidelines. Additionally, the stress modeling and analysis performed during the component redesign was reviewed and no discrepancies were noted. The manufacturer also reviewed the reengineered tie bolt service history and several tie bolts with between 5,000 and 9,000 cycles were taken out of service for examination. Component examinations and database reviews failed to show any similar failures within the fleet.
The tie bolt installation required that the bolt length be measured in order to determine the exact stretch of the bolt after the nut was torqued to specification. The original stretch requirement was used with the redesigned tie bolt to eliminate confusion during assembly. A subsequent service bulletin and FAA airworthiness directive mandated that the older design be removed from service, but the installation stretch requirement was not modified. To mitigate future tie bolt fractures, Rolls-Royce reduced the stretch requirement on the tie bolt during the assembly process. As a result, the mean stress on the tie bolt was reduced. The reduced stretch is also expected to increase both high and low cycle fatigue margins in the part. The assembly instructions were updated with the new stretch callout during the first quarter of 2008.
Probable Cause: The uncontained engine failure due to the fatigue failure of the gas producer turbine tie bolt.
Accident investigation:
 |
|
Sources:
NTSB CHI06GA241
History of this aircraft
Other occurrences involving this aircraft
| 4 May 2016 | N629JK | Rotor Blade LLC | 1 | Manitowoc County NW of Maple Grove, WI | |
sub |
| Collision with pole or wires | ||||||
Revision history:
| Date/time | Contributor | Updates |
|---|---|---|
| 08-Oct-2022 06:30 | ASN Update Bot | Added |
| 31-May-2023 05:12 | Ron Averes | Updated |
Corrections or additions? ... Edit this accident description
The Aviation Safety Network is an exclusive service provided by:
Quick Links:
| ASN Home | Send Correction / Feedback |
| FSF Home | Disclaimer | Copyright |
| Contact Us | Privacy Policy |
| Press / Media |
CONNECT WITH US:
©2024 Flight Safety Foundation