ASN Wikibase Occurrence # 352393
This information is added by users of ASN. Neither ASN nor the Flight Safety Foundation are responsible for the completeness or correctness of this information.
If you feel this information is incomplete or incorrect, you can
submit corrected information.
Date: | Thursday 28 October 1999 |
Time: | 21:32 LT |
Type: | Boeing 757-222 |
Owner/operator: | United Airlines |
Registration: | N575UA |
MSN: | 26689/515 |
Year of manufacture: | 1993 |
Total airframe hrs: | 23631 hours |
Engine model: | P&W PW2037 |
Fatalities: | Fatalities: 0 / Occupants: 68 |
Aircraft damage: | None |
Category: | Serious incident |
Location: | Chicago, IL -
United States of America
|
Phase: | En route |
Nature: | Passenger - Scheduled |
Departure airport: | Washington-Dulles International Airport, DC (IAD/KIAD) |
Destination airport: | San Francisco International Airport, CA (SFO/KSFO) |
Investigating agency: | NTSB |
Confidence Rating: | Accident investigation report completed and information captured |
Narrative:The pilot reported, "We encountered substantial vertical control flutter FL310-350 .78-.80 Mach with left, center, right autopilot and no autopilot. Flutter stopped when IAS was decreased. Descended to FL310, 250 kts., .75 Mach and had no more flutter. The flight diverted to O'Hare Airport and made an uneventful landing. Maintenance inspections revealed excessive free play in the elevator flight controls. The allowable limit is 0.340 inch and 0.50 inch was measured. The free play was corrected in accordance with the current maintenance manual. The bushings, the left center power control actuator (PCA), two reaction links, and four ilder links were replaced. During a subsequent test flight, vertical oscillations were still present. Further maintenance action included replacing all elevator hinge bearings and four PCA's. The third flight test was successful and the airplane was returned to service. Inspection of two reaction link rod ends revealed axial and radial wear which exceeded allowable limits. Inspection of the 16 hinge bearings revealed 3 bearings had axial and radial wear which exceeded limits and had moderate to severe corrosion. On October 11, 2001, the FAA issued Airworthiness Directive (AD) 2001-20-11 that was applicable to all B-757 series airplanes to "prevent unacceptable airframe vibration during flight, which could lead to excessive wear of elevator bearings and result in reduced controllability of the airplaneâ¦" The AD required, "Before further flight after the free-play checks, lubricate the bearings in the elevator PCA load loop and hinge line." Lubrication of the hinge bearings had not been required in a previous AD. The new AD required recurrent inspections every 18 months instead of the previous requirement of 4,000 hours, or 3,000 hours for some models. On January 28, 2001, Boeing issued a maintenance manual revision that corrected improper instructions for elevator free-play checks. The improper procedures in the maintenance manual had been in effect from September 20, 1997, to January 28, 2001.
Probable Cause: the in-flight vibration of the airplane's elevator due to excessive freeplay in the elevator control system. Factors included the corrosion of the elevator PCA reaction link bearings and the elevator hinge bearings, excessive axial and radial wear of the elevator PCA reaction link bearings, the inadequate procedures for lubricating the elevator hinge bearings, and the incorrect procedures for measuring elevator free play.
Accident investigation:
|
| |
Investigating agency: | NTSB |
Report number: | CHI00IA018 |
Status: | Investigation completed |
Duration: | 2 years and 7 months |
Download report: | Final report |
|
Sources:
NTSB CHI00IA018
Revision history:
Date/time | Contributor | Updates |
07-Mar-2024 13:32 |
ASN Update Bot |
Added |
07-Mar-2024 13:34 |
ASN |
Updated [Operator, Nature, Departure airport, Destination airport, Narrative] |
The Aviation Safety Network is an exclusive service provided by:
CONNECT WITH US:
©2024 Flight Safety Foundation